Wiring questions - whole house remodel

So what technical question or comment is on your mind!
New Member
Posts: 1
Joined: 31 Oct 2013, 20:48

Wiring questions - whole house remodel

Postby derekxc » 31 Oct 2013, 21:33

I'm sorry if this has been covered already somewhere and I missed it. I would have looked longer, but my contractor is a couple of days away from drywalling everything up, and I think my electrician doesn't know as much as he says he does.

Right now, we're down to studs, and he has run the following wires:
RG6 from the satellite dish and cable box into the central closet
RG6 from the central closet to each HDTV around the house (8 or 9)
RG6 from the media room (the only Blu-Ray player) to the central closet where I hope to someday have a Matrix Switcher
Cat 5 from the central closet to each HDTV around the house for streaming, firmware updates, etc.

1. He assures me the RG6 is what he uses for his HDTVs, but do I need particular HDTVs to get 1080p out of an RG6?
2. I've never heard of using RG6 as the output from a Blu-Ray player. I don't even know if I will ever actually want to play my Blu-Ray around the house, but I figured I should wire it while I could.
3. I would really prefer NOT to have a cable box or satellite receiver under/next to every TV, but I have no idea how to change the channel if I don't have a box at which to point the remote. I would also prefer not renting 8 or 9 boxes, which is where the Matrix Switcher comes in.
4. Assuming we get this all to work the way we want it to, are there other devices besides the Blu-Ray that I should consider pumping out to all the other TVs? If so, what cables should I use for it/those?
5. The audio is all going to be separate from the TVs, but I don't know what sources we will use. They are all fed from the media room and will have volume controls in the walls of the rooms, at least to start.

The irony in all of this is that my wife and I watch about 2 hours of TV a month, but maybe we'll watch more if we have it in the kitchen and master bathroom and the patio...

Anyway, I'm sorry (again) for the newbie (and possible redundant) questions, but I appreciate your advice and suggestions for the 4 Qs/Cs.

Thanks in advance,

Major Contributor
Major Contributor
Posts: 484
Joined: 07 Dec 2006, 04:14
Location: Oklahoma

Re: Wiring questions - whole house remodel

Postby eliwhitney » 01 Nov 2013, 07:07

To: derekxc

You've covered a LOT of territory in that Posting!

A) - TOO Late now, but it might have been better to have engaged a Local Audio Expert House to have handled all that cabling ...??

... E.G. - YES, your Gentleman does certainly profess that he 'knowns more' than he actually does, in that zero output from your Blue Ray can be done w/ RG-6!!! ... MUST BE certified, CL-2 (in-the-walls) HDMI exclusively, with the attendant footage restrictions!

B) - Signals into a Home Cable Box {Satellite, too} can be done O.K. w/ RG-6 BUT never as an 'Output.' This, too, must be the same as for the Blu-Ray. Unless w/ very unique 'HDMI' {usually Custom-made from Internet Companies such as http://www.Bluejeanscable.com } .. your 'runs' s/b as short as possible!


Major Contributor
Major Contributor
Posts: 484
Joined: 07 Dec 2006, 04:14
Location: Oklahoma

Re: Wiring questions - whole house remodel

Postby eliwhitney » 01 Nov 2013, 07:16

... P.S. - - - here's some more for you to peruse?


eli - - - and, 'F.Y.I.' .... I am in No Way Whatever associated w/ them !! ...just have had {Good Fortune} whenever using them.

Posts: 32
Joined: 03 Mar 2008, 16:28

Re: Wiring questions - whole house remodel

Postby rml » 01 Nov 2013, 08:35

Your electrician has already shown he doesn't really understand what is required. Your biggest problems here are first time, and second convincing your contractor to do some things he will think are a waste of time and money. RG6 is fine for cable, satellite, and over the air TV distribution(OTA). As has already been said, forget HDMI over RG6.

In a nutshell,

1) do double runs of RG6 from your central closet to each terminal point (star topology) (remember, cable is cheap, cheap);

2) forget CAT5 and forget CAT5e, which is over 10 years old and has much greater bandwidth that CAT 5. Do double runs of CAT 6 (gigabit Ethernet) in the same star topology as the RG6. Cable is cheap, http://www.monoprice.com charges around $155 for a 1,000 foot roll of in-wall rated CAT6.

If you do these two things, you preserve your options. (You will also need cable feeds to your central closet for the outside source signals for cable, satellite dish(s), over the air TV antenna and the cable/dsl modem (for high speed internet)). I'd also consider "whole house surge suppression."

To expand on the above,

1. RG6 is what you need for conventional runs from the cable or satellite company. If your contractor fights you on dual runs, point out that satellite dish runs already require dual runs due to the bandwidth requirements of all the transponders.

2. Cable is cheap. Also, if you want over the air local tv reception, that will require additional RG6 runs as well. Conventional over the air HD broadcasts can still offer the best HD signals, second only to bluray. If your builder tells you you don't need it because cable and satellite rebroadcast the local stations, tell him to run dual RG6 distribution lines anyway. Unless you have fiber to your home; e.g., FIOS, you will discover the cable and satellite companies are delivering softer and softer "HD" signals because they can cram in more channels by lowering the channel bandwidth (bit rate) which lowers the HD content delivery quality). Finally, cable and satellite companies are always fighting with the local broadcasters over licensing fees which result in blackouts and are also prone to imposing blackouts for other unfathomable reasons. Bandwidth, flexibility and redundancy are the central ideas.

3. Currently, if the cable source is DISH, they have their Hopper/Joey system that allows 1 big receiver/digital video recorder box to distribute the signal to a tv connected directly to itself and to 3 other tvs through a much smaller box. Multiple big boxes can be networked for more than 4 sites. Competitors will undoubtedly offer similar solutions, but not for a while. These receivers all have RF remotes and will work through walls.

4. You won't get HDMI 1080p signals out of RG6 unless you buy a pair of RG6 to hdmi converter boxes for each point to point link in your network; further, they are currently expensive ($100-$300 a pair). Long HDMI cable runs become expensive and impractical (repeaters or fiber optic cable).

5. You will get HDMI out of your satellite and cable boxes and from them you run an HDMI cable to your TV or to your Audio Video Receiver and from it to your TV.

6. I'd start out with one good bluray player. For example, an Oppo digital bdp-103 (a bdp-105 if you have audio/videophile tendencies and the budget), connected to your AVR (audio video receiver) in your media room by HDMI cable for HD audio and directly to your TV for the video. After that, unless you watch movies in bed, I'd buy secondary bluray players; they've become quite inexpensive (as low as $30).

7. I'd forget the idea of martix switching over RG6. HDMI over ethernet is much cheaper. For example, while not matrix but broadcast, a 1x8 (8 room) HDMI Amplifier Splitter over CAT5e/CAT6 Complete Solution Kit for cable runs upto 164ft is $271 at http://www.monoprice.com. Point-to-point switching, if needed, is not that much more. If the wire is in place, you can always swap out the electronics.

8. NO CAT5 Ethernet and NO CAT5e Ethernet cable. Insist on CAT 6 (gigabit ethernet) for your ethernet backbone cableling. If your contractor fights you on this, he is ignorant. Don't let him talk you out of it. If you have to, go buy a box or two of CAT6 yourself and give it to him. If you have time, it is much cheaper to buy over the net. As I said above, a 1,000 ft box of in-wall rated CAT6 cable is $155 at Monoprice.com. As with the RG6, I'd run dual backbone CAT6 cables, especially if you are really considering matrix switching audio/video over cable.

9. Depending on your budget and available time, you could also run conduit. For example, visualize 1 to 2 inch in-wall pvc pipe (cheap) from basement to attic with junction boxs in each floor; drop at least 3 or 4 pipes so you can reach any room/closet from any other room. You don't have to put anything in them now. Futureproof your house unless your are not planning on staying. Will you need it? Who knows. I did it in a house I built in 1981 and it didn't take long (10 years) for the 1" (inside diameter) pipe I used to fill up.

10. Back to matrix switching. Run your CAT6 IP network in a star topology with your gigabit ethernet switch as the hub in your central closet. You will probably need at least a 16 port, non-blocking, gigabit matrix switch; but these are commonly available for under $100 (of course you can pay a lot more). You can/will soon be able to do all the wired audio/video streaming/switching/distribution you want over your IP network. For now, also run your second CAT6 HDMI audio/video network using the same topology. Remember, cable is cheap, cheap, cheap and it takes essentially the same time to run two cables as one. Did I say cable is cheap?

11. Finally, more and more devices also have wireless ethernet capability. Even speaker wires are going wireless (no standards yet). This can eliminate a lot of device to device cables. Audio and 1080p video streaming over wireless ip is pretty good, as long as your wireless access point(s) can handle your bandwidth demands. This is true whether your source is over the net or from your home network file server (most of which will require a wired connection to a wireless access point). Why do you need in-house cable anyway? Wired connections are far more reliable and can handle far more bandwidth. Wireless may be the future but it cannot yet supplant wire totally. Even if it could, do you want to be continuously bombarding yourself with many more, admittedly low power, high frequency wave transmissions?

Much is left unexplained and unsaid and what has been said mainly reflects my biases. Good luck.

Posts: 6
Joined: 26 Mar 2014, 01:03
Location: San Diego

Re: Wiring questions - whole house remodel

Postby markwinstanley » 06 Aug 2014, 02:37

IR Extender will be best option for changing channels on satelllite/cable box. You have to tamper your STB if it don't have port for connecting IR Extender. Simply open stb and and attached all IR Extender wire on IR light bulb. For more information and rest of queries about Structured Cabling can be solved by Telesystemscorp.

Return to “HD Video and Audio Technical Discussions”

Who is online

Users browsing this forum: No registered users and 1 guest